pasobchild.blogg.se

1. Cisco ise 2.4 configuration guide install#
2. Cisco ise 2.4 configuration guide license#
3. Cisco ise 2.4 configuration guide download#

We recommend that you use the GUI due to the following We recommend that you have a repository size of minimum 100 GB for all types of deployment (small, medium, and large). You can create the following types of repositories: Restore operation, can be performed with the backup files of previous versions of Cisco ISE and restored on a later version.įor example, if you have a backup from an ISE node from Cisco ISE, Release 1.3 or 1.4, you can restore it on Cisco ISE, Release 2.1.Ĭisco ISE, Release 2.4 supports restore from backups obtained from Release 2.0 and later.Ĭisco ISE allows you to create and delete repositories through the administrator portal. Is required to resume the services on your Cisco ISE deployment. Quiesces the file system to maintain crash consistency, which can cause your Cisco ISE functionalities to freeze. When a backup is initiated by VMware or any other third-party backup service like CommVault SAN level backup, it Using VMware snapshots or any third-party backup service to back up Cisco ISE data might result in interrupting Cisco ISE You use the backup functionality included in Cisco ISE for archival and restoration of data. Restoring a snapshot might cause database replication and synchronization issues. In a multinode Cisco ISE deployment, data in all the nodes are continuously synchronized with currentĭatabase information. When Cisco ISE is run on VMware, VMware snapshots are not supported for backing up ISE data.Ĭisco ISE does not support VMware snapshots for backing up ISE data because a VMware snapshot saves the status of a VM atĪ given point in time. Backup can be done via the primary PAN GUI or using the CLI Operational Data-Contains monitoring and troubleshooting data. Via the primary PAN using the GUI or CLI. Backup can be done from the CLI orĬisco ISE allows you to back up the following type of data:Ĭonfiguration data-Contains both application-specific and Cisco ADE operating system configuration data. Recovery of Secondary Node in Case of Failure in a Distributed DeploymentĬisco ISE allows you to back up data from the primary PAN and from the Monitoring node.Recovery of Primary Node in Case of Failure in a Distributed Deployment.Recovery of a Node Using New IP Address and Hostname in a Standalone Deployment.Recovery of a Node Using Existing IP Address and Hostname in a Standalone Deployment.Recovery of Lost Nodes Using New IP Addresses and Hostnames in a Distributed Deployment.Recovery of Lost Nodes Using Existing IP Addresses and Hostnames in a Distributed Deployment.Recovery of Lost Nodes in Standalone and Distributed Deployments.Synchronize Primary and Secondary Nodes in a Distributed Environment.Export Authentication and Authorization Policy Configuration.Restore a Monitoring Backup with a Monitoring Persona.

Restore a Monitoring Backup with Administration and Monitor Personas.Restore a Monitoring (Operational) Backup in a Standalone Environment.Restore Configuration Backups from the GUI.Restoration of Configuration or Monitoring (Operational) Backup from the CLI.Enable RSA Public Key Authentication in SFTP Repository.Monitoring and Troubleshooting Service in Cisco ISE.Enable Your Switch to Support Standard Web Authentication.Configure Client Provisioning in Cisco ISE.

Cisco ise 2.4 configuration guide download#

It might be cheaper to purchase a single SKU of the new ISE 2.4 TACACS license. Not sure what the cost difference is, especailly if you only need 1 PSN active. I think most people purchase the old 2.3 SKU and then get 50 PSN entitlements.

Cisco ise 2.4 configuration guide license#

If you enable Device Admin Service on two nodes (with only 1 license) then you will get a license warning.

Cisco ise 2.4 configuration guide install#

But 2.4 licenses are now per PSN.īUT - if you only want to buy ONE 2.4 TACACS license and only process TACACS on ONE PSN, then you strictly only need to purchase and install one license. In pre-2.4 days, you bought 1 TACACS SKU, and that entitled you to 50 PSN licenses. If you enable it on one node only, then only 1 license will be consumed. This means that if you have 1 TACACS license installed on the PAN node, and you have not enabled TACACS Service (Device Admin), then 0 TACACS licenses will be consumed. In ISE 2.4 the TACACS license consumption is dynamic.